Manufacturing
Products: power line poles, lighting, masts, telecom towers
Steel multi-sided poles and metal structures for power engineering, infrastructure and telecom. We design, manufacture and galvanize; installation is carried out by a licensed construction partner company.
Energy
Overhead power line masts
Multi-sided poles for 6–220 kV and lattice poles for 35–750 kV
from UAH 55,000
Substation gantries
Multi-sided gantries for 35–750 kV and typical ones for 35–500 kV
from UAH 80,000
Lightning protection masts and air-termination rods
Lightning protection masts 5–40 m on multi-sided shafts
from UAH 15,000
Overhead line fittings and crossarms (0.4-10 kV)
Crossarms, caps, clamps and bolts for 0.4–10 kV lines
from UAH 500Communications and telecom
Outdoor lighting
Street lighting columns
Park, street and road columns 3–12 m
from UAH 3,800
High-mast lighting
Floodlight masts PM and PMV, fixed or mobile crown
from UAH 40,000
Stadium lighting
Masts and lighting layouts for stadiums, football pitches and courts
from UAH 40,000
Foundation anchor cages and bolts
FPO, FPM and FKM anchor cages for poles and masts
from UAH 1,500
Brackets, caps and crossarms
KO and KP brackets, OG caps, TR crossarms
from UAH 1,000Transport
Special structures
What we make and how the product families relate
The base of most products is a bent multi-sided shaft (the sheet is bent on a press, the longitudinal seam is welded, flanges are welded on where needed) or a lattice structure made of angle steel; the fittings for 0.4–10 kV lines (crossarms, clamps, caps) are the exception. Loads, height and purpose differ.
- power engineering: overhead power line masts, substation gantries and fittings and crossarms for 0.4–10 kV lines for reinforced concrete poles;
- lighting: street lighting columns, high-mast lighting, stadium lighting and brackets, caps and crossarms;
- foundations: foundation anchor cages and bolts for lighting columns, floodlight masts and catenary masts;
- transport and roads: catenary masts, traffic signal poles, CCTV poles;
- telecom: multi-sided telecom masts and lattice antenna masts;
- protection and symbols: lightning protection masts, flagpoles.
One pole, several functions
The families can be combined: a catenary mast carries insulated cable (SIP) and luminaires, a telecom mast carries lighting and an air-termination rod, a lightning protection mast can also be a lighting column.
Comparing the families: use, parameters, coating
| Family | Use | Typical parameters | Coating |
|---|---|---|---|
| Overhead power line masts | Power lines | Lines of 6–10, 35, 110, 220 kV; typical poles 35–750 kV | Galvanising, optionally painted |
| Substation gantries | Substations | 35, 110, 150, 220, 330, 500 kV | Galvanising |
| Fittings and crossarms for 0.4–10 kV lines | For reinforced concrete line poles | TN and TM crossarms, clamps, caps; albums 3.407.1-143 and 3.407.1-136 | BT-577 varnish, galvanising by special order |
| Street lighting columns | Streets, parks, roads | 3–12 m; ranges PMO, PLO, PKO, UMO, UKO, DMO | Galvanising, average thickness at least 55 µm (3 mm wall) or 70 µm (4 mm wall) per ISO 1461 |
| High-mast lighting | Stadiums, ports, airports | PMV 20, 24, 30 and 34 m; up to 16 floodlights | Galvanising |
| Stadium lighting | Stadiums, football pitches, tennis courts | Masts of 15–30 m for football and 8–10 m for tennis; the lighting calculation and floodlight selection are free | Galvanising |
| Brackets, caps and crossarms | Lighting columns and floodlight masts | KO brackets (1 to 4 arms) and KP brackets (1 to 3 arms), OG caps, TR crossarms | Galvanising |
| Foundation anchor cages and bolts | Foundations for lighting columns, floodlight masts and catenary masts | FPO, FPM, FKM cages (FPMV for PMV masts); anchors M20–M42 | No coating (per the catalogue) |
| Catenary masts | Trams, trolleybuses | BKMG and BKM range for ground installation, 7.3 and 9 m; load 800–2500 kg; other sizes to order | Galvanising, optionally painted |
| Telecom masts | Base stations | Multi-sided, up to 70 m | Galvanising |
| Antenna masts | Radio and radio-relay antennas | Lattice, up to 70 m (completed projects) | Galvanising or painting |
| Traffic signal poles | Junctions | Posts, cantilever and gantry poles; reach set by the project | Galvanising, optionally painted |
| CCTV poles | Sites, roads, railways | A post with a bracket; height and reach to suit the task | Galvanising, optionally painted |
| Lightning protection masts | Building and structure protection | MO range, 5–40 m | Galvanising or painting |
| Flagpoles | Government, commercial, private sites | 6–70 m | Galvanising or paint or varnish coating |
Where galvanising is listed, it is hot-dip, to DSTU EN ISO 1461:2024. The values are taken from the family pages; a calculation confirms them for your site.
How to choose a pole or mast
- Task. What the pole has to carry: luminaires, a camera, antennas, conductors, a catenary or a flag. This sets the type, a multi-sided shaft or a lattice tower; for lighting also the profile, see multi-sided or conical poles.
- Loads and wind region. Mass and area of the equipment, conductor tension, wind and ice regions, terrain type; wind pressure values W0 for regional centres are in Wind Regions of Ukraine.
- Height and reach. Mounting height of the equipment, reach of the bracket or cantilever; for lighting see How to Choose the Height of a Lighting Pole; for masts and towers see Height of a Telecom Mast or Tower.
- Base fixing. Either a flange on an anchor cage or direct embedment in the ground; the foundation depends on it, see Foundation Anchor Cages FPO, FPM, FKM; foundation types and choice by soil are in Foundations for Masts, Towers and Power Line Poles.
- Coating. The main coating is hot-dip galvanising, with paint when needed; where aviation marking is required, red-and-white signal painting (tall towers and masts, including those near airfields).
- Documents and inspection. Agree the list of documents and the scope of weld inspection before fabrication starts.
Materials, galvanising and production
The basis is our own full production cycle: cutting, press bending, welding and galvanising.
Preparing a product for the bath: Designing for Hot-dip Galvanising; the service: Hot-dip galvanising. Items longer than the bath, such as poles, are galvanised in sections.
| Parameter | Value |
|---|---|
| Main steel grades | St3, S245, S345, 09G2S |
| Sheet bending | 2000 t press; sheet up to 25 mm thick and up to 12 m long |
| Sheet cutting | Plasma: sheet up to 2 × 6 m, 300 A power source; laser: sheet up to 2 × 12 m, 6 kW |
| Own galvanising bath | 13,000 × 1,600 × 3,200 mm (length × width × depth) |
| Powder coating | Oven with a working chamber: height 1.8 m, width 1 m, length 6 m |
| Shop capacity | 500 t per month |
| Product warranty | 2 years |
Inspection during production
Incoming metal inspection, dimensional checks, visual and ultrasonic inspection of welds, zinc thickness measurement, laboratory control; welding is done by qualified welders. More in Quality Control of Steel Structures and Custom steel fabrication.
What to send for a calculation
Send what you know:
- the product family, type of pole or mast, quantity;
- height, reach of the bracket or cantilever;
- loads: mass and area of luminaires, antennas or cameras; for lines the voltage, number of circuits, conductor grade and cross-section;
- wind and ice regions, terrain type, soils;
- fixing (flange or ground), coating, scope of inspection and documents;
- KM or KMD drawings or a technical specification form, lead time and delivery address.
Leave blank any item you do not know; we will clarify it.
Forms and data lists by product: How to Order Poles and Masts.
Products: frequently asked questions
How is a multi-sided pole different from a lattice tower?
A multi-sided pole is a solid bent shaft with a longitudinal seam; a lattice tower consists of legs and bracing and lets the wind pass through. We choose the type by height, loads and site conditions.
What steel and coating do you use for poles?
The main steel grades are St3, S245, S345 and 09G2S. The base coating is hot-dip galvanising in our own bath, optionally with paint (BT-577 varnish is standard for fittings for 0.4–10 kV lines).
What is the lead time?
Typically 3–4 weeks if the product is not in stock. We give the exact time after the calculation.
How much does a pole cost?
Lighting poles cost from UAH 3,800 to 39,000 each depending on the range and height (indicative, as of September 2026, including VAT): Lighting Pole Prices. Brackets and crossarms are not included in the pole price: they have a separate price list (see Brackets, crossarms and caps). Galvanising costs UAH 20–38 per kg including VAT (also indicative, as of September 2026), see what the price depends on. Other products are priced from your parameters.
Can I order a product to my own drawing?
Yes. We fabricate to the customer’s KM or KMD drawings; without drawings, Steel structure design can help. There is no minimum order for hot-dip galvanising.
Do you perform X-ray testing of welds?
No. We check welds visually and by ultrasound; if the design requires X-ray testing, tell us when you enquire.
What is the warranty on the products?
The warranty period for our products is 2 years.
Get a quote for your requirements
Send us your requirements — we will calculate the price and lead time.